Skip to main content

Introduction

tutorial made on a Peugeot 3008 1.6 HDi 16V FAP 110 hp

  1. Steps 1-5 are intended to make it easier to access the EGR valve. Remove the wiper arms. Mark their position before removal. The use of a wiper arm puller is usually necessary. Place the gaskets on each side
    • Steps 1-5 are intended to make it easier to access the EGR valve.

    • Remove the wiper arms. Mark their position before removal. The use of a wiper arm puller is usually necessary.

    • Place the gaskets on each side

  2. Remove the central screw
    • Remove the central screw

    • Remove the brake fluid reservoir screws

    • Remove the brake fluid reservoir (be careful not to spill any fluid).

  3. Unclip the windshield trims by pushing them towards the inside of the windshield, and remove them Move aside the awning grille and extract the water evacuation hoses from the front wings, on each side
    • Unclip the windshield trims by pushing them towards the inside of the windshield, and remove them

    • Move aside the awning grille and extract the water evacuation hoses from the front wings, on each side

    • Unclip and remove the awning grille

  4. Remove the fixing screws on each side Remove the 6 staples to remove the crosspiece. Remove the cross member.
    • Remove the fixing screws on each side

    • Remove the 6 staples to remove the crosspiece.

    • Remove the cross member.

    • Remove the air duct screws

    • Unclip and remove the air duct

  5. Remove the 3 staples with a screwdriver
    • Remove the 3 staples with a screwdriver

    • Remove the apron insulation

    • Remove the engine cover

  6. Remove the 3 Torx screws from the air filter housing cover
    • Remove the 3 Torx screws from the air filter housing cover

    • Disconnect the air flow meter connector

    • Loosen the air filter feed duct clamp

    • Detach from the air filter housing by pulling it towards you

    • Also disassemble the air duct

    • Remove the cover and the air filter housing. Take the opportunity to dust or change the air filter if necessary.

    • Access to the EGR valve is possible

  7. This operation remains difficult due to the lack of visibility and accessibility, the valve being located at the rear of the engine. Disconnect the connector Remove the 2 EGR valve fixing screws
    • This operation remains difficult due to the lack of visibility and accessibility, the valve being located at the rear of the engine.

    • Disconnect the connector

    • Remove the 2 EGR valve fixing screws

    • Remove the collar using a screwdriver. To reinstall it, this is easily done by tightening it using multi-grip pliers or small pliers.

    • Remove the EGR valve , being careful not to lose the gasket.

    • Clean the joint plane, then reassemble everything.

Finish Line

13 other people completed this guide.

david.mathonneau

Member since: 11/21/2015

303 Reputation

1 Guide authored

13 Comments

Well done 🤗 great tutorial!! On the 2L HDi 150 is it in front?

adil.halla20 - Reply

Good morning,

Where is the one for 3008 phase II from 2016 1.6 BlueHDi 120?

Thank you in advance

l.achahboun2 - Reply

Good morning

I would like to change the fuel pressure sensor on a Peugeot 3008 1.6l 112hp, can someone tell me where this sensor is located please, I can't find any information on the net, thank you and have a nice day everyone.

Sincerely

Aziz Drissi - Reply

Hello, the fuel pressure sensor is located on the injection rail below the EGR valve.

frank monnier -

Good morning

very good tutorial.

and for a 2008 where is the EGR valve located?

Thanks in advance for the answers

Alexandre Grillot - Reply

Add Comment

View Statistics:

Past 24 Hours: 17

Past 7 Days: 127

Past 30 Days: 509

All Time: 70,462