Parts
-
-
Unlock the plastic cover by turning it 1/4 turn with a large flat screwdriver.
-
Remove the plastic cover
-
Unscrew the 2 headlight fixing screws (with une clé a pipe de 10)
-
the headlight is fitted, you have to pull to get it out of its housing
-
-
-
You must hold the headlight during the entire operation to avoid tearing an electrical wire.
-
The bulb holder is fixed by 4 lugs, spread them one by one to open the headlight
-
Do not force too much, the fasteners are made of plastic, there is a risk of breakage
-
the lighthouse is open
-
feu clignotant -
feu stop -
night light (LED, no bulbs to replace)
-
-
-
Turn the bulb 1/4 turn to release it from the holder
-
Compare the new and old bulb (base, power, etc.)
-
Replace the new bulb on the holder
-
-
-
Replace the gasket if necessary.
-
Clip the 2 parts of the headlight together
-
Check that they are all locked correctly
The seal goes back into the groove of the bulb holder (black plastic) and not on the headlight.
FABRICE GAUDIER - Resolved on Release Reply
-
-
-
Insert the headlight notch into the plastic stud
-
Insert the key into the rubber pad
-
Revise the 2 screws of 10
-
Replace the plastic cover and turn the fastener 1/4 turn
Thank you very well done. I would say it is level 1.5.
This helped me a lot because I don't even know where the car manual is anymore, it doesn't fit in the glove compartment.
Hervé DUPRE - Resolved on Release Reply
-
Cancel: I did not complete this guide.
12 other people completed this guide.
12 Comments
A huge thank you for this timely tutorial. Obviously, with my characteristic bad luck, I came across the only left rear light that refused to come off easily. So much so that I tested it on its right brother to see if it was me or it :-). Well, by passing a flexible plastic spatula between the bodywork and the light, it came off like a big boy without forcing.
I saved 15-20€ at the garage thanks to you and I feel less stupid in front of my car!
Herve
herve.foucher - Resolved on Release Reply
Hello, for me it's the right rear position light that no longer works. I don't understand what the bulb is: is it the same as the indicator? Thank you
luciole555fr - Resolved on Release Reply
Hello, I have the same problem...did you get an answer? Did you find a solution?
Thank you, it saved me time and above all I didn't get angry with the car...
Patrice DANIEL - Resolved on Release Reply
Hello JM, were you able to disassemble this connector?
I am installing a universal tow bar harness and need to be able to identify the wires…
THANKS,
Aymeric
Aymeric BASQUIN - Resolved on Release Reply
Good morning,
Thank you very much for sharing this information.
FABRICE GAUDIER - Resolved on Release Reply
Hello
I wanted to remove the connector for added security by lifting the orange locking piece of the connector on the schematic.
I pulled the connector very hard and couldn't get it to unplug. It was as if something else had to be done to get it to unlock.
Thanks for anyone who can help me.
JM GOIRAND
Jean-Michel GOIRAND - Resolved on Release Reply
For the 1/4 turn
a coin will do too!
Thanks for the tutorial
cedric koslowski - Resolved on Release Reply
Hello, I just did the procedure and it only took me 5 minutes.
To remove the plastic latch I used the ignition key and it works perfectly.
farid tebache - Resolved on Release Reply
THANKS !
What a time saver! I replaced the brake light on the right rear light, no difficulty after reading your tutorial and seeing the photos, 5 minutes is enough.
Tip for those who don't have a screwdriver large enough to turn the plastic latch [red step 1]: use a metal cutlery handle (fork, teaspoon, etc.), flat and straight.
Cedric Grandemange - Resolved on Release Reply
