Skip to main content

Introduction

Do you want to change the bulbs in your 207+ tail light? This tutorial will help you do it easily.

  1. This tutorial is made on a 207 phase 2.
    • This tutorial is made on a 207 phase 2.

  2. To remove the tail light, you do not need any tools. Open your trunk then look behind the fire inside , you will find a screw to unscrew by hand . Once the nut is completely removed , gently pull the light towards you , moving it up and down to unclip it.
    • To remove the tail light, you do not need any tools.

    • Open your trunk then look behind the fire inside , you will find a screw to unscrew by hand .

    • Once the nut is completely removed , gently pull the light towards you , moving it up and down to unclip it.

    • Only one clip is present on the fire.''

  3. You will then need to pinch the small tab on the plug and pull towards you to remove it completely. You will then need to pinch the small tab on the plug and pull towards you to remove it completely. You will then need to pinch the small tab on the plug and pull towards you to remove it completely.
    • You will then need to pinch the small tab on the plug and pull towards you to remove it completely.

  4. For unclip the fire plate , you should already have spotted the 4 clips. Press the clips one by one and pull towards you to remove. Be careful not to break the clips so be gentle.
    • For unclip the fire plate , you should already have spotted the 4 clips.

    • Press the clips one by one and pull towards you to remove.

    • Be careful not to break the clips so be gentle.

  5. - Rouge : Feu stop / Position.
    • - Rouge : Feu stop / Position.

    • - Green: Fog light.

    • - Orange: Flashing

    • - Purple: Reversing lights

  6. To change a light bulb , nothing could be simpler: Press the bulb then rotate it to one side then pull it towards you.
    • To change a light bulb , nothing could be simpler:

    • Press the bulb then rotate it to one side then pull it towards you.

    • For in put a new one , you position the bulb in the place provided for this purpose then press on it and rotate it to one side.

  7. Represent the turntable on your fire, the clips must be opposite the levers used to clip it. Press firmly on the plate to clip it in place.
    • Represent the turntable on your fire, the clips must be opposite the levers used to clip it.

    • Press firmly on the plate to clip it in place.

    • If some clips do not fit, pull the red tab then press on the plate so that it clips.

  8. For put the fire connector back , put the plug back in respecting its direction thanks to the small tab then press firmly to clip it. For put the fire connector back , put the plug back in respecting its direction thanks to the small tab then press firmly to clip it. For put the fire connector back , put the plug back in respecting its direction thanks to the small tab then press firmly to clip it.
    • For put the fire connector back , put the plug back in respecting its direction thanks to the small tab then press firmly to clip it.

  9. Put the fire back on respecting its meaning , once in place, press firmly on it to clip it. Screw the nut that is in the car trunk behind the tail light. You can tighten it as much as possible so that it doesn't move anymore.
    • Put the fire back on respecting its meaning , once in place, press firmly on it to clip it.

    • Screw the nut that is in the car trunk behind the tail light.

    • You can tighten it as much as possible so that it doesn't move anymore.

Finish Line

8 other people completed this guide.

Florian HOUART

Member since: 06/20/2016

7,791 Reputation

50 Guides authored

One Comment

very good thank you

gine.serra - Reply

Add Comment

View Statistics:

Past 24 Hours: 7

Past 7 Days: 63

Past 30 Days: 318

All Time: 33,862