Parts
-
This step is untranslated. Help translate it
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>As a safety precaution, disconnect one of the terminals from <strong><a href="https://pieces-auto.oscaro.com/batterie-...>the battery</a></strong></p></body></html>
-
-
This step is untranslated. Help translate it
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>Remove the plastic cover by rotating the 6 black clips a quarter turn (place in a horizontal position).</p></body></html>
-
-
This step is untranslated. Help translate it
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>Unscrew the 3 bolts of 8.</p></body></html>
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>Unplug the power plug from the ramp.</p></body></html>
-
-
This step is untranslated. Help translate it
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>Unscrew <strong><a href="https://pieces-auto.oscaro.com/bougie-d-...>the candles</a></strong> using your spark plug wrench.</p></body></html>
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>Be sure to unscrew them as straight as possible, to avoid damaging the thread.</p></body></html>
-
-
This step is untranslated. Help translate it
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>Place the new spark plugs in their locations</p></body></html>
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>Screw them in by hand until they are tight.</p></body></html>
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>Tighten the spark plugs a quarter turn using your wrench.</p></body></html>
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>Be careful not to damage the threads when reassembling the spark plugs.</p></body></html>
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>You can apply a layer of suitable grease to avoid any risk of seizure.</p></body></html>
-
-
This step is untranslated. Help translate it
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>Reposition the ignition rail and plug it in.</p></body></html>
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>Put the plastic cover on and turn the clips a quarter turn (vertical position).</p></body></html>
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>You can then start your engine.</p></body></html>
-
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN" "http://www.w3.org/TR/REC-html40/loose.dt...> <html><body><p>Your engine speed may have dropped slightly after changing the spark plugs.</p></body></html>
-
Cancel: I did not complete this guide.
7 other people completed this guide.
5 Comments
I don't use grease, just tighten to the torque and no problem....
Hello, it is advisable to put grease on the thread, you should not empty the whole pot on it, a small amount is enough. Personally I went to a garage they did not put any grease and I ended up with broken levers in the well.... I was happy afterwards!
Never grease the threads of a spark plug otherwise it will become clogged with the risk of damaging the thread the next time you disassemble it.
I wonder if it would not be better to add a little copper grease to the spark plug thread to prevent rust between the thread and the tapping, thus avoiding in the future the possibility of spark plugs seizing in the cylinder head?
Yes indeed it may be a good idea! But respecting the tightening torque indicated by the manufacturer it is not essential. So far I have never encountered a seized spark plug. In addition I try to change the spark plugs fairly regularly, it plays an important role in the combustion of the engine! It limits the risks of seizure...
I will still indicate this possibility on the tutorial!