Skip to main content

Introduction

The model presented is an Audi A4 B8 2.0 TDI 150Cv

Warm up the vehicle before starting the oil change so that the oil is more fluid

  1. Raise the vehicle and secure it on jack stands Open the hood
    • Raise the vehicle and secure it on jack stands

    • Open the hood

    • Remove the engine cover by pulling it upwards

  2. Loosen the oil filter using the ratchet with the large extension and the 30 socket. Loosen the oil filter using the ratchet with the large extension and the 30 socket. Loosen the oil filter using the ratchet with the large extension and the 30 socket.
    • Loosen the oil filter using the ratchet with the large extension and the 30 socket.

  3. Unscrew the T25 screws Remove the engine cover Place a bin under the vehicle
    • Unscrew the T25 screws

    • Remove the engine cover

    • Place a bin under the vehicle

    • Unscrew the oil pan plug using a 19 mm wrench.

  4. Remove the oil filter by pulling on it Remove the three gaskets using a small screwdriver Remove the three gaskets using a small screwdriver
    • Remove the oil filter by pulling on it

    • Remove the three gaskets using a small screwdriver

  5. Replace the three seals Check that the new oil filter matches the old one Clip the new oil filter
    • Replace the three seals

    • Check that the new oil filter matches the old one

    • Clip the new oil filter

  6. Reinstall the new oil filter onto the engine, starting by hand tightening it. Finish tightening using the ratchet
    • Reinstall the new oil filter onto the engine, starting by hand tightening it.

    • Finish tightening using the ratchet

  7. Once the oil has stopped flowing, replace the cap and tighten it using the 19 wrench. Reassemble the plate under the engine
    • Once the oil has stopped flowing, replace the cap and tighten it using the 19 wrench.

    • Reassemble the plate under the engine

    • Tighten the T25 screws

    • The cap seal cannot be replaced.

  8. Remove the filler cap Pour in the oil recommended by the manufacturer ON THIS MODEL THERE IS NO OIL GAUGE, THE LEVEL IS DONE ON THE ON-BOARD COMPUTER ON THE MMI
    • Remove the filler cap

    • Pour in the oil recommended by the manufacturer

    • ON THIS MODEL THERE IS NO OIL GAUGE, THE LEVEL IS DONE ON THE ON-BOARD COMPUTER ON THE MMI

    • Once the oil has been poured into the engine, check the filler cap and start the engine for a few seconds to fill the oil filter.

  9. Check and adjust the oil level using the MMI Click on the CAR key Select oil level
    • Check and adjust the oil level using the MMI

    • Click on the CAR key

    • Select oil level

    • Adjust the oil level if necessary

    • The engine must be at operating temperature to check the oil level.

  10. Go to Maintenance Periodicity Indicator Click on "Reset oil change interval" Click on "Reset oil change interval"
    • Go to Maintenance Periodicity Indicator

    • Click on "Reset oil change interval"

Finish Line

7 other people completed this guide.

charly bontemps

Member since: 11/22/2016

13,501 Reputation

49 Guides authored

17 Comments

Hello, thank you very much

julien0201 - Reply

Hi

After draining, a message “maintenance due” is always displayed despite having reset in MMI.

Thank you for answering me

chehabfayal - Reply

Hello everyone ,

I changed the engine oil on this model, to check and adjust the oil level using the MMI the oil level was at 90%, once I got home. I wanted to check the oil level again and I noticed that the oil level had dropped to 40%. I wonder if it's not a sensor that's playing up. Thank you for your answers

servair75 - Reply

Hello everyone!

I would like to know if someone could provide me with the exact reference of the filler cap please?

Thank you so much !

sebastien gri - Reply

I emptied a liter and still the same message, being about 4 liters suddenly

can someone help me?

virlouvet johny - Reply

Add Comment

View Statistics:

Past 24 Hours: 5

Past 7 Days: 55

Past 30 Days: 201

All Time: 44,196