Skip to main content

Introduction

This tutorial will help you change your bulbs, those in the ceiling light as well as the trunk on a Peugeot 207.

  1. 
On our 207 phase 2 inside we have 2 lighting modules:

- Ceiling light at the front of the vehicle with one bulb.
    • On our 207 phase 2 inside we have 2 lighting modules:

    • - Ceiling light at the front of the vehicle with one bulb.

    • - Right side trunk light with one bulb.

  2. 
Before you start disassembling the ceiling light, please turn it off using the button.

Place a flat screwdriver in the hollow on the left side then do lever gently.

Put your fingers to block the left side then do the same from the right side then lever and pull down the ceiling light to unclip it.
    • Before you start disassembling the ceiling light, please turn it off using the button.

    • Place a flat screwdriver in the hollow on the left side then do lever gently.

    • Put your fingers to block the left side then do the same from the right side then lever and pull down the ceiling light to unclip it.

    • Don't hesitate to force it a little if it doesn't come out the first time, while being careful not to break the clips.

  3. 
Please removed the connector who holds the ceiling light in pressing the tab and pulling it.

Please removed the connector who holds the ceiling light in pressing the tab and pulling it.
    • Please removed the connector who holds the ceiling light in pressing the tab and pulling it.

  4. 
On the ceiling light a transparent plastic hide the bulb, with your fingers, use lever to unclip all the small clips that are located around the ceiling light.

On the ceiling light a transparent plastic hide the bulb, with your fingers, use lever to unclip all the small clips that are located around the ceiling light.

On the ceiling light a transparent plastic hide the bulb, with your fingers, use lever to unclip all the small clips that are located around the ceiling light.
    • On the ceiling light a transparent plastic hide the bulb, with your fingers, use lever to unclip all the small clips that are located around the ceiling light.

  5. 
For remove the bulb, use a small flat screwdriver, return the module and press the bottom of the bulb, this one will therefore fall, replace it by putting a new bulb.

Use only a W5W or T10 model bulb!

Use only a W5W or T10 model bulb!
    • For remove the bulb, use a small flat screwdriver, return the module and press the bottom of the bulb, this one will therefore fall, replace it by putting a new bulb.

    • Use only a W5W or T10 model bulb!

  6. 
Once you have clip the clear plastic on the ceiling light, connect the connector by simply respecting its meaning.

Clip the ceiling light into the roof of the vehicle, passing before the top then press the clips hard so that he fits in well.

Turn on your ceiling light to check if it works properly.
    • Once you have clip the clear plastic on the ceiling light, connect the connector by simply respecting its meaning.

    • Clip the ceiling light into the roof of the vehicle, passing before the top then press the clips hard so that he fits in well.

    • Turn on your ceiling light to check if it works properly.

    • If the bulb does not work, please remove it and then turn the bulb the other way and try again.

  7. 
For unclip the trunk module, you will need to use a small flat screwdriver by leveraging from the right side you will be able to take it out then finish by hand gently to remove it.

For unclip the trunk module, you will need to use a small flat screwdriver by leveraging from the right side you will be able to take it out then finish by hand gently to remove it.

For unclip the trunk module, you will need to use a small flat screwdriver by leveraging from the right side you will be able to take it out then finish by hand gently to remove it.
    • For unclip the trunk module, you will need to use a small flat screwdriver by leveraging from the right side you will be able to take it out then finish by hand gently to remove it.

  8. 
For remove the bulb from the trunk, use your small flat screwdriver by prying from below the bulb, do you like your fingers to take it out.

Replace the bulb by clipping it into the same place.

Use only a W5W or T10 bulb.''
    • For remove the bulb from the trunk, use your small flat screwdriver by prying from below the bulb, do you like your fingers to take it out.

    • Replace the bulb by clipping it into the same place.

    • Use only a W5W or T10 bulb.''

  9. 
For reclip the module, go left side first then press the right side hard enough so that it clips back into the compartment.

For reclip the module, go left side first then press the right side hard enough so that it clips back into the compartment.
    • For reclip the module, go left side first then press the right side hard enough so that it clips back into the compartment.

Finish Line

2 other people completed this guide.

Laura RICHE

Member since: 06/28/2016

559 Reputation

5 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 1

Past 7 Days: 14

Past 30 Days: 78

All Time: 12,939